Stories & guides · · 27UsedCar
Tire Basics: How to Read the Sidewall, Judge Wear and Know When to Replace
A tire's sidewall is a printed data sheet: size, load index, speed rating and even its production week. Learn to decode it, judge tread wear and age, and know the damage that means replace now, not later.

Tires are the only part of a car that touches the road, yet most buyers glance at them for two seconds during an inspection. A tire's sidewall is actually a printed data sheet: it tells you the size, the load and speed the tire is built for, and even the week it was manufactured. Learning to read it takes ten minutes and will save you money on every used car you ever assess.
Decoding the size: 205/55 R16 91V
Take the most common marking format as an example — 205/55 R16 91V:
- 205 — the tread width in millimetres.
- 55 — the aspect ratio: the sidewall height is 55% of the width.
- R — radial construction, used by virtually all modern passenger tires.
- 16 — the wheel diameter in inches the tire fits.
- 91 — the load index, a coded maximum weight per tire (91 corresponds to 615 kg).
- V — the speed rating, the maximum sustained speed the tire is certified for (V = 240 km/h). Common ratings run from S (180 km/h) and T (190 km/h) through H (210 km/h) to V and above.
When replacing tires, match the size and never go below the load index or speed rating specified on the vehicle's door-jamb placard or owner's manual. That placard — not the sidewall — also gives the correct inflation pressure. The "MAX PRESS" figure molded into the sidewall is the tire's absolute limit, not your target pressure.
The DOT code: a tire's birth certificate
On US-market tires, look for the letters DOT followed by a string of characters. The last four digits are the production date: the first two are the week, the last two the year. A code ending in 3524 means the tire was made in week 35 of 2024. The full code may appear on only one sidewall, so check both sides. In other markets, an equivalent date marking appears near the DOT or E-mark — the four-digit week/year format is the part to find.
This matters because rubber ages even when a tire is barely used. Michelin advises that after five years of service, tires should be inspected regularly by a professional, and that a ten-year-old tire should be replaced whatever its wear and mileage. The US National Highway Traffic Safety Administration (NHTSA) similarly notes that some vehicle manufacturers recommend replacing tires every six years regardless of use — and its guidance is to check each tire's age as part of routine inspection.
Tread depth and wear bars
Tread grooves channel water away from the contact patch; as they shallow, wet grip and braking distances suffer. Tires carry molded tread wear indicators — small raised bars across the main grooves. When the tread surface wears down level with these bars, the tire is at roughly 2/32 of an inch (1.6 mm) of remaining depth, the minimum in many jurisdictions and the point at which NHTSA notes traction drops rapidly. In practice, wet-weather performance degrades well before that: many safety experts treat around 3 mm as the sensible replacement point for a car that regularly drives in rain.
You do not need special tools: a tread depth gauge costs very little, and even a coin gives a rough check. Measure in several places across the tread, not just the centre.
Reading wear patterns
Uneven wear is a free diagnosis of the car's recent life:
- Wear on both shoulders — chronic under-inflation.
- Wear in the centre — chronic over-inflation.
- Wear on one edge only — wheel alignment (camber or toe) out of specification.
- Scalloped or patchy wear — worn dampers or unbalanced wheels.
On a used car, patterns like these are not only a tire cost to budget — they hint at maintenance habits and possible suspension work ahead.
Damage and age: when replacement is not optional
Replace a tire immediately, regardless of tread depth, if you find bulges in the sidewall (internal structure failure), deep cuts exposing cord, cracks from age or ozone, or a puncture in the sidewall or shoulder area. Tread-area punctures can sometimes be repaired by a trained professional — only an internal inspection can confirm whether the tire ran under-inflated and damaged its structure.
A practical routine
NHTSA recommends inspecting tires at least once a month and before long trips: check pressures when cold (the tires should not have been driven on for at least three hours), look over tread and sidewalls for cuts, punctures, bulges and cracks, and do not forget the spare. A tire that loses pressure repeatedly, or a car that vibrates at speed, needs a professional look rather than another top-up.
For used-car buyers, the summary is simple: budget for tires if any of the following are true — tread near the wear bars, mixed brands or sizes on one axle, a DOT date more than about six years old, or visible sidewall damage. On an otherwise good car, a set of tires is a predictable, negotiable cost — discovering the problem after purchase is what makes it expensive.
Sources
Editorial review: 27UsedCar ·


